(dissenting).
It is my opinion that the petition for rehearing should be granted. It shows, I respectfully suggest, that the majority opinion a is predicated on factual premises, which materially affected the result, either not in accord with the record or shown to be unfounded by a demonstration at the hearings in this court and the trial court, of the physical exhibits in operation.
The majority opinion in effect states that the orbital movement, more accurately described as movements in varying directions all within a defined orbit, present during the operation of an internal combustion engine, mounted in accordance with the claims in suit of patents 1,843,907 and 1,890,871, results from the fact that the front and rear mountings are in line with an axis passing below the center of mass (concentric with the crankshaft); that this renders the engine top heavy and out of balance and makes necessary the resilient mountings; and that the alleged infringing devices avoid such orbital movement because the axis between the two mountings passes through the center of mass and suspends the engine unit in balance. |
Such orbital motion is present in the alleged infringing devices where the engines are suspended in balance, and will transmit vibrations to the frame, body and propelling mechanism of the automobile when resilient mountings are not employed. This fact was- established by the simple experiment of substituting a rigid front mounting for the resilient one in one of the alleged infringing devices and operating the motor. Plaintiff’s evidence as to this experiment and what it showed was not disputed. This movement can also be observed with the eye and felt with the tip of one’s finger when the alleged infringing device is in operation. It varies with the speed of the engine but its presence is beyond doubt. This conclusion is corroborated by the fact that in all the commercial devices manufactured and sold by Chrysler Corporation the pivotal supports, which carry the engine unit, are mounted in or on resilient rubber.
The operation of an internal combustion engine produces vibrations other than those caused by torque reaction. These other vibrations are due to lateral, vertical and diagonal resultant forces and they are present and must be cushioned regardless of whether the engine unit is or is not in. balance on its pivotal mountings. Pivotally mounting the engine and letting it oscillate with substantial freedom will overcome the effect of torque reaction, but it is necessary to employ resilient mountings to overcome the effect of such other forces.
In patent ’907 Trott seats the mountings in or on resilient rubber. In patent ’871 Trott employs a transverse spring mounted on the front axle which provides, in effect, a resilient front mounting.
Trott combined front and rear pivotal mountings, carrying substantially all of the *203weight of the engine unit and allowing substantial freedom of oscillation, with resilient seats at the pivot points, especially the front pivot point, and thereby solved the problem of eliminating the effect of all the vibratory forces and preventing their communication to the frame, body and propelling mechanism of the automobile.
The majority opinion states in effect that the axis passing from the front to the rear mountings of the devices constructed in accordance with the claims in suit of patents ’907 and ’871, must be below the center of mass. In other words, that Trott taught to mount the engine on pivot points or supports positioned below the center of mass so that it would be out of balance.
It is true that Trott emphasized placing the front and rear mountings as nearly as • possible in line with the longitudinal axis of the crankshaft — and in that he no doubt was in error with respect to certain types of engines — but he did not teach mounting the engines out of balance. In fact he taught the opposite.
In his specification in ’907, he said:
“These pivotal mountings may be concentric with the crankshaft 7 of the engine, or vertically or laterally spaced therefrom •within reasonable limits, and depending on conditions and requirements.
“That is, if not concentric with the engine shaft, these pivotal mountings may be located in the longitudinal central vertical plane of the power plant unit if the weight thereof will thus be balanced, or laterally off center in either direction if the weight of the power plant unit is not equally distributed on either side of said plane.” (Italics mine.)
It will be noted he said the mountings may be vertically or laterally spaced from the axis of the crankshaft “depending on conditions and requirements” “if the weight” of the power plant “will thus be balanced.”
This shows Trott taught that departure may be made from the crankshaft axis,' both vertically and laterally, but not so as to throw the engine out of balance.
It must also be kept in mind that Trott’s mountings áre for different types of engines including aeroplane engines and marine craft engines where a mounting in line with the crankshaft axis would be through the center of mass and would suspend the engine in balance.
Figure 1 of the patent drawing in patent ’907 shows an automobile engine with the mountings above the axis of the crankshaft and figure 7 shows an aeroplane engine with the mountings concentric with the crankshaft.
Deo. 1, 1931.
1,834,907
R. S. TROTT ENGINE MOUNTING Piled May 27, 1929.
only about 2 inches above the crankshaft axis. When applied to a Ford engine, the mountings- illustrated in figure 1 would be approximately in line with an axis through the center of mass. In the Plymouth engine manufactured by Chrysler Corporation, the center of mass is several inches above the crankshaft axis, necessitating a much higher front mounting, but Trott taught that such departure could be made.
I conclude that in patent ’907 Trott taught to suspend the engine approximately in balance but to position the mountings as nearly in line with the crankshaft axis as conditions permit.
In patent ’871, the engine unit is mounted pivotally at the rear and at the front on a transverse spring carried on the front axle. Such spring permits a pivotal movement. While the spring itself is below the center of mass it permits such freedom of movement by the engine unit, that the unit, in operation, finds its normal axis of oscil*204lation, an axis through the center of mass, and in fact oscillates about that axis. This also was demonstrated by the operation of the physical exhibits at the hearings in this court and the trial court. The axis of oscillation in line with the center of mass can be plainly discerned with the naked eye, by observing while the engine is running, the movement of a metal rod vertically mounted on the front of the motor. This device is operative and effectually solves the vibration problem. It is the device that was disclosed and demonstrated to Chrysler Corporation’s representative. Lee substituted for the spring mounting a resilient rubber mounting pivotally supported,- at the front end of the normal axis of oscillation.
Trott discovered and demonstrated the principle that an engine mounted so as to permit it to oscillate with substantial free-, dom about its normal axis of oscillation will overcome the effect of the vibrations produced by torque reaction. No doubt Lee’s mounting is an improvement over the spring means employed by Trott but it employs Trott’s principle and produces its appropriate result.
In pivotally mounting the engine unit, front and rear in patent ’907 and pivotally at the rear and on the transverse spring in front in patent ’871, so as to permit substantial freedom of movement about an axis of oscillation, Trott made a revolutionary departure from the teachings and practices of the prior art, — one so unorthodox that automotive engineers would not have accepted it as practical until Trott’s discovery and demonstration. Indeed, until one sees the actual demonstration, it is difficult to believe that an internal combustion engine unit could be permitted such freedom of movement and still properly perform its appropriate function.
When Trott. combined such pivotal mounting, substantial freedom of oscillation and front and rear mountings seated in resilient supports, carrying substantially all of the weight of the engine unit, he produced a new and useful combination not disclosed by the prior art and effectually solved the problem of eliminating the effect on the frame, body and propelling mechanism of the several vibrations produced by the several resultant forces generated in the operation of internal combustion engines.
As stated in my dissent to the majority opinion herein, Trott’s approach to the problem was new. Prior efforts had been directed toward restraining the resultant forces, as for example in the Royce patent number 1,108,242, by frictional resistance and springs to prevent oscillatory movement. In others the restraint is sought to be accomplished by providing supports with vibration rates different from the vibration rate of the engine so that the engine vibrations do not synchronize with the natural frequency of the supports, (Lee patent number 1,743,612' and Akimoff French patent number 536,360); and by providing different vibration rates at the several supports, so that the vibration rates of the several supports do not synchronize with each other, (Lee patent number 1,743,512). On the contrary, Trott’s conception is to give substantial freedom to the normal movements of the engine unit. He overcomes the vibratory effects by permitting substantially normal oscillatory movements in mountings resiliently seated, that carry substantially all of the weight of the engine unit.
In patent ’871, the vibrations are not communicated to the tires as stated in the majority opinion. This was shown by a demonstration at the hearings, here and below, of an engine, mounted in accordance with patent ’871, in an automobile supported on rigid blqcks, where no vibration was communicated to the frame, body and propelling mechanism.
Lee adopted Trott’s conception but elevated the front pivotal mounting sufficiently to obtain a suspension of the engine unit in perfect balance. He thus overcame any side thrust resulting from imperfect balance and no doubt produced an improved result. But he solved the vibration problem by the use of Trott’s combination and Trott’s conception. He simply made a change that enabled the Trott combination to produce its appropriate result in a more perfect way. He at most effected an improvement.
In my former dissent I agreed that patent ’871 was not infringed. I am now convinced that both ’871 and ’907 are valid and infringed.
For the reasons stated, I respectfully dissent from the order denying the petition for rehearing.
Where the words “majority opinion” are used herein the reference is to the first majority opinion.