(charging jury). The first machine for making lead pipe by pressure was the Burr machine, which was constructed in 1820. In that machine, the core which formed the bore of the pipe was fastened into the face of the ram, and extended through the cylinder and into the dié. Burr was the first person to whom it occurred that lead pipe could be made out of set or hard lead, by means of pressure. This machine was his contrivance to carry that idea into practical effect. It virtually failed, especially so in respect to the manufacture of pipe of the usual or ordinary size. It seems, from the testimony, to have been successful so far as respected the manufacture of pipe of two inches or two inches anu a half in diameter, and above that size; but, for the ordinary size —under two inches — it was a failure, and it went out of use. What constituted the real difficulty in the way of the successful operation of the Burr machine is a matter of controversy, as you have seen during the course of this trial.
In 1837, an improvement was made upon this machine of Burr by the Hansons, which went into successful operation. This machine was patented by them in England on the 21st of August, 1837. The improvement consisted in making a bridge at the bottom or near the bottom of the cylinder, for the purpose of holding a short core, and was founded upon the. development of a new and beautiful idea. They had discovered, for the first time, that lead, like steel or iron, was susceptible of being welded together after separation when solid; and they were thus enabled to construct a bridge at the bottom or near the bottom of the cylinder, in which they could insert a short core, where it could be kept firm and steady. The lead had to be forced through *712the apertures in this bridge, which separated the mass when in a solid state; but it became re-united and welded together by means of pressure in the chamber beneath the bridge, and in the formation of the pipe as it was forced out of the die. The improvement was successful, and enabled the Hansons to make good merchantable pipe, and to make it cheaper and better than by any previous mode of manufacturing it, so that it superseded all prior methods of making lead pipe. The correctness of this idea, that lead could be separated when hard, and re-united by pressure, like the re-union of welded iron or steel, has been fully established on a trial in this court, in which the Hanson machine was involved. The truth of this idea was denied by the most eminent chemists in New York upon that trial, and, as a consequence of their disbelief of the fact that this property belonged to the metal, they testified that the pipe was made, in the Hanson machine, while in a fluid state, because the welding of the lead in a set state was a physical impossibility. They stated that they had never known this property as belonging to lead. But the fact was proved, by actual experiment on the trial, to their entire satisfaction, and they afterwards came into court and admitted they were mistaken.
Now, although this machine thus constructed manufactured merchantable pipe, and superseded all modes of manufacture known at that time, yet it was subject to an imperfection which embarrassed the manufacturer. The re-union of the lead, after its separation in passing through the bridge, was not at all times' complete throughout the length of the pipe made from a given charge; and hence, when the pipe was subjected , to a considerable pressure of water, a flaw would sometimes appear. This, I believe, was the only defect ever imputed to the article manufactured by the Hanson machine.
The next improvement upon the Burr machine was the plaintiffs’, in 1841 — the one in question in this suit. They bored the solid ram of Burr, and, instead of fastening the core on the face of the rain, extended it through the ram, and fixed it firmly to the cross-head of the frame — the core extending, also, through the cylinder into the die. The bore of the ram is fitted to the core or core-holder, either by adapting the aperture to it, or by packing, so that, when the machine is put in operation, the ram slides upon the core. The core, in the first place, is fastened to the cross-head, which is firm and immovable, differing in this respect from the Burr machine, in which the core was movable with the ram, being fastened upon its face. The core in the plaintiff’s machine is also steadied by the aperture in the hollow ram, or by packing. The advantage in this over the arrangement of Burr, is in steadying the core or core-holder, and in preserving its centrality in reference to the die. This machine appears to have been entirely successful in the manufacture of lead pipe of any dimension.
I will now call your attention to what is claimed as new in the plaintiffs’ patent. After the description of the construction of the machine, which is minutely given, the paten-tees wind up by claiming, first, “the long core or core-holder, formed and held stationary with relation to the dies, as described;” and, secondly, “the constructing of the piston B hollow, in the manner described, and the combination of the same with the long core or core-holder upon which the piston slides.” The third claim relates to the reversed arrangement of the machinery in the working machine, which it is not important to describe.
The first and third claims are not in controversy, and may be left out of the case. The dispute between the parties is confined to the second claim. It is insisted by the plaintiffs that the peculiar arrangement covered by that claim gets rid of the defect in the Burr machine, of the unsteadiness of the core in the manufacturing of pipe of the ordinary size, and also gets rid of the defect in the Hanson machine, because it dispenses with the bridge; and that this arrangement has been infringed by the defendants. The arrangement enables the plaintiffs to use a strong core or core-holder, and to fix it firmly at the cross-head, and, by the aperture in the ram and the packing, to preserve its centrality in relation to the die; by reason of which they have succeeded in making perfect pipe. This is, in substance, the new arrangement of the plaintiffs, and these are the advantages which they claim to have derived from the change, and from the improvement upon the previous machines.
Let me now call your attention to the construction of the defendants’ machine. This, also, is claimed to be an improvement on the Burr machine. It was constructed some five or six years after the plaintiffs’ improvement. It is arranged by boring the solid ram of Burr, and placing the die in the face of it, at the same time closing the bottom of Burr’s cylinder, and fixing the core firmly at the bottom, where Burr’s die was placed. The core extends through the cylinder and into the die thus fixed in the face of the ram. In the operation of the machine, the core passes through the die and into the hollow ram nearly the length of it. the pipe, of course, passing through the same aperture above.
It will be necessary for you to examine the arrangement aud construction of' these two machines, in the particulars that I have mentioned, with great care and attention, because the determination of the case will hinge mainly, if not exclusively, upon the judgment you shall form in respect to them and their operation. In other words, the case depends upon the opinion you shall form of the substantial identity or -want of identity between the two, as it respects the arrangement of the hollow* piston and the core or core-holder found in them, and the operation and effect of the same in the manufacture of pipe. If, in looking at the arrangement and combination of the two, you arrive at the conclusion that they *713are substantially the same, then the use of the defendants’ is an infringement of the plaintiffs’. If, on the contrary, you arrive at the conclusion that they are not substantially the same, then the defendants will be entitled to your verdict.
These questions of identity between two opposing machines are frequently exceedingly difficult, and often the most difficult questions involved in these patent cases. The question is ultimately one of fact, and the jury must examine it with a consciousness that they are to be responsible for its determination.
There are some principles of law bearing upon these questions which may shed some light upon your examination of them, and which it is proper should be stated. A change in form from the construction of an existing machine, is not a substantial change in the eye of the patent law; nor is a change in proportions. These changes require no great ingenuity, at all events they do not call for the exercise of the inventive faculties. They are simply the work of a mechanic of ordinary skill, and, therefore, are entitled to no particular consideration when we are inquiring into the question of identity between the construction of two machines. So. also, the substitution of a mechanical equivalent, as it is termed, in the construction of a machine, is not a substantial change. There are many devices in construction that can be made by a skilful mechanic, differing very much from each other in appearance, but which, in the eye of the patent law, are regarded as identical. For instance, an inventor, in the construction of his machine, desires a given power, in order to give practical operation and effect to his discovers'. One mechanic may furnish the power by means of a lever, another by means of a screw — two very different instruments —yet. so far as the use of the instruments and so far as their purpose to furnish the power is concerned, they are regarded simply as mechanical equivalents, and the use of one in one machine does not distinguish that machine, from a machine in which the other is found. So, too, a given power may be obtained by a spring or by a weight, or by a pulley — apparently very different devices. Tet, as .they are used for the same purpose, and to accomplish the same end in machinery, they are regarded as substantially identical. It is also proper to state, in this connection, that a patentee is not confined to the precise arrangement, in the construction of his machine, which he has described in his patent. This is obvious from the principles already stated. Formal changes are notning —mere mechanical changes are nothing — all these may be made outside of the description to be found in the patent; and yet the machine, after it has been thus changed in its construction. is still the machine of the patentee, be cause it contains his invention, the fruits of his mind, and embodies the discovery which he has brought into existence and put into practical operation. A familiar illustration of the principle that I am endeavoring to develop, and one bearing directly upon the issue between the parties here, will be found in the instance of the large core-holder or core described in the plaintiffs' patent. It is said, that the description in the patent is confined to a large core or core-holder. But, admitting this to be so, the change to a small one, if a small one can be used successfully, is but a change in proportions, as the larger includes the smaller one. Any person that could make a large one could make a small one, and could pack it to fit the aperture in the ram just as well as the large one, without anything more than the application of a little common sense, and ordinary skill in the working of the machine.
In addition to these instances which 1 have' given you, in which the patentee is not tied down to the precise description given in his patent, there is another suggestion I wish to make, in connection with this branch of the tease, and it is one that commends itself to the common sense of the jury. Any machine which has been constructed as an improvement upon a previous one, or as an entirely new manufacture, may be very considerably changed in its mechanical arrangement and construction, the description of it may be very much departed from in the construction, and yet it may accomplish the object and purpose for which it was designed. It may not be as perfect, in producing the result intended, but still it may, though changed and varied very much, do its work satisfactorily. It is proper also to remark, that any change or alteration which is suggested to the skilful operator from the working of the machine, and in the course of its operation — any useful change that may be the result of the practical working of the machine — is clearly a change that belongs, not to the operator, but to the original inventor of the improvement. Upon this branch of the case, and in this line of observation, I wish to guard you from falling into any error, because I am desirous that you shall comprehend accurately and clearly the principles of law that properly enter into the examination and decision of this difficult and somewhat metaphysical question. I, therefore, wish to prevent your being misled into extending these principles beyond the fair limit and scope that belong to them. What I mean to say is this — that, in order to ascertain and determine whether the change in the arrangement and construction of an existing machine is to be considered as a substantial change or not, you must ascertain and determine whether the change is the result of mechanical skill, worked out by mechanical devices — of a knowledge that belongs to that department of labor — or whether the change is the result of mind, of genius, of invention, in which you discover something more than mere mechanical skill and ingenuity. A change in the arrangement and construction *714is not substantial, unless you find embodied in it, over and beyond the skill of the mechanic, that inventive element of the mind which is to be found in every machine or improvement that is the proper subject of a patent. If you find that, then the change is a substantial one, that entitles the party to a patent. Then it is a change that has added something to the useful knowledge of mankind and to the business interests of the country.
It will be seen, from these observations, that a difference in the mechanical arrangement and construction of the two machines is not necessarily a test by which to determine that the two are not identical. They may be, apparently, very different externally, and still embrace the same substantial identity in principle or mode of operation. . So, on the other hand, the converse of the proposition is equally true. The two may, apparently, be very similar externally, and still, in principle and mode of operation, be very different. I do not know any better mode of examining a question of this kind, than to inquire whether the mechanical arrangement and construction of the two embrace the same set of ideas, the same leading features or ideas, which, in practical operation, produce the useful result. In other words, whether the arrangement and combination of the parts of machinery found iu each are substantially the same, and operate in substantially the same way in producing the result. Heuce, the real question in this case, as it respects the identity of the two machines, looks simply to their mechanical arrangement and construction, as to whether or not the defendants’ incorporates, in its strúeture and operation, the spirit and substance of the plaintiffs’ improvement — that is, uses the arrangement and mechanism of the plaintiffs’ to perform the same functions or produce the same effect in the same way, or substantially the same way.
I will read to you two passages upon this branch of the case, which embody very fully and clearly the views that I desire to impress upon you, and which, being in the words of another, (Chief Justice Tindal, of the common pleas,) may, perhaps, take hold of your minds more strongly, from the variety of the illustration, than anything that I have said or could say. Iu Walton v. Potter, Webst. Pat Cas. 590, Curt. Pat. § 255, note 1, Chief Justice Tindal remarked: “Now, there can be no doubt whatever, that although one man has obtained a patent for a given object, there are many modes still open for other men of ingenuity to obtain a patent for the same object; there may be many roads leading to one place; and, if a man has, by dint of his own genius and discovery, after a patent has been obtained, been able to give the public, without reference to the former one, or borrowing from the former one, a new and superior mode of arriving at the same end, there can be no objection to his taking out a patent for that purpose. 'But he has no right whatever to take, if I may so say, a leaf out of his neighbor’s book, for he must be contented to rest upon his own skill and labor for the discovery, and he must not avail himself of that which had before been granted exclusively to another; and, therefore, the question again comes around to this — whether you are are of opinion that the subject-matter of this second patent is perfectly distinct from the former, or whether it is virtually bottomed upon the former, varying only in circumstances which are not material to the principle and substance of the invention.” I read another passage from the same case. Webst. Pat. Cas. 586, Curt. Pat. § 202, note 1: “Where a party has obtained a patent for a new invention, or a discovery he has made by his own ingenuity, it is not in the power of any other person, simply by varying in form or in immaterial circumstances, the nature or subject-matter of that discovery, to obtain either a patent for it himself, or to use it without the leave of the patentee, because that would be, in effect and in substance, an invasion of the right; and, therefore, what you have to look at upon the present occasion, is not simply whether, in form or in circumstances, that may be more or less immaterial, that which has been done by the defendants varies from the specification of the plaintiff’s patent, but to see whether, in reality, in substance and in effect, the defendants have availed themselves of the plaintiff’s invention in order to make that fabric, or to make that article which they have sold in the way of their trade; whether, in order to make that, they have availed themselves of the invention of the plaintiff.”
There is one other observation that I desire to make, and that is a practical one, which bears more directly upon the real point in issue between these parties than perhaps any of the general observations to which I have called your attention. You have seen that, after all, the case comes down to this naked question, as it respects this branch of it, and that is, whether or not the defendants’ machine embraces, within its arrangement, the combination of the hollow ram and core or core-holder, patented-to the plaintiffs. I am bound to say that I do not think the question is simply whether or not the defendants use the hollow ram in combination with the core; because I think that the combination of the hollow ram and the core or core-holder alone and in the abstract, is not the invention or improvement of the plaintiffs. Cylinders, sliding upon rods, had previously existed in mechanical constructions and in practical use, which is all that is found in the combination of the hollow ram and the core or core-holder upon which the hollow ram slides. That aloDe, and in the abstract, is not the invention of the plaintiffs, and. although the hollow ram and the core in combination may be found in *715the defendants’ machine, that alone will not constitute an infringement. The quesuon, in my judgment, is this. It has been conceded throughout, that the plaintiffs were the first persons who applied this peculiar combination to the purpose of making lead pipe by pressure. They were the first to conceive of the adaptation of this peculiar combination (which of itself was not new) to the purpose of producing this useful, and practical result; and it is in this idea that the novelty of their improvement consists. The point in the ease is, whether or not the defendants have applied this combination substantially in the same way for the same purpose. If they have, then they have appropriated the improvement which belongs exclusively to the plaintiffs, and the use of their machine is an infringement of the plaintiffs’ patent. To this point you must turn your attention, and upon this, in my judgment, the question on this branch of the ease must turn. Have the defendants applied this combination of the hollow ram and the core substantially in the same way that the plaintiffs have applied it, for the purpose of making lead pipe by pressure? If they have, they are guilty of infringing; if they have not, then they are not guilty.
The remarks which I have made to you thus far apply simply to the question of the identity of the mechanical arrangement and construction of the two opposing machines. There is another question involved in the case, which bears upon this, and to which it is necessary to call your attention. The defendants contend that, admitting there is an apparent substantial identity in the arrangement and construction of the two machines, and in their principle of operation, yet, in point of fact, the practical operation and effect of the two upon the mass of lead, in forming the pipe, are essentially different, and that such effect in the defendants’ is highly beneficial in the operation of the machine. In other words, that because the defendants’ forms the pipe at the point of pressure, at the face of the ram, the operation and effect of the power thus used upon the mass of lead are new. In this view of the ease, and in respect to this branch of it. the law looks more to the result of the mechanical arrangement than to the arrangement itself. The new and different effect in the operation of the machine reflects back upon the mechanical arrangement and construction. and characterizes the change, and may authorize an inference of a substantial change, which the arrangement, disconnected from the new and different effect, would not. Without connecting the new effect with the change, the change might be only formal and unsubstantial. The case of the improvement in the mould-board of the east-iron plough referred to by some of the learned counsel, illustrates this principle. It was there held, that a change in the shape of the mould-board, though apparently formal and one of proportion, and of itself amounting to nothing, ■became a substantial change by producing, a new and different effect, in its operation, from that which was produced in the previous plough. It must be borne in mind, however, that the new effect, which is to give such materiality and importance to the ap-. ■parently formal change, must not be looked. for in the simple production of a larger quantity of pipe in a given time, or in the reduced amount of power required to operate the machine. All this may depend upon other considerations, as upon superior mechanical skill in the construction and arrange-, ment of the machinery. But the new euect to which I am now calling your attention must be different in kind. The operation and effect upon the lead in the defendants’ machine must be new and different from the operation and effect upon the lead in the plaintiffs’. And the capability of the de-. fendants’ machine to make a greater quantity of pipe in a given time, or to use a reduced amount of power, must be the result of the new and different operation and effect of the arrangement upon the mass of lead. This principle, which has been brought into the defense in this case, is, in the aspect in which it is presented, a very important one. I am desirous, therefore, that you should thoroughly comprehend it, and also the qualifications which belong to it, and which should be kept in mind in applying it
It is well known that new machines which have been devised for the purpose of carrying into practical effect an improvement or invention, oftentimes exhibit, when first constructed, and until tested by practical use, great imperfections in their results. It requires time and experience, and the observation derived from the practical working of the machine, to perfect it. Hence, the mere fact that a machine constructed and arranged, apparently or externally, like a previous one, produces a result more beneficial, is not always a safe test to determine that the two are substantially different. The result may be one derived from experience in the use of the previous machine. The new result, in the present case, must be a result derived from a different mechanical operation and effect upon the mass of lead in the cylinder, and not from the same operation and effect. This is a question of fact, and you will readily, from the time that has been consumed upon this branch of the case, call to mind the evidence bearing upon it — first, the examination of the experts on both sides,, as regards the difference in the operation and effect of the two machines upon the mass of lead, in producing the pipe — also, the various experiments, many of them exhibited in your presence, others made elsewhere and detailed by the experts, tending, on the one side, to make out tnis new and different effect upon the mass of lead, in manufacturing pipe, and, on the other side, to discredit and disprove it. The question is thus raised, up*716on this evidence, for your determination. You must decide on which side the weight of the evidence lies. If it is in favor of the view taken by the defendants, -that there is a new and different operation and effect upon the mass of lead in the cylinder, on account of the arrangement in the defendants’ machine, then, I think, as a matter of law, that such new operation and effect give character to the mechanical arrangement- and afford evidence of a substantial change. If, on the other hand, you think that the weight of the evidence is with the plaintiffs, and that there is no material or essential difference in the effect and operation of the two machines upon the mass, then you will be •obliged to go back to the first question presented to you — whether or not there is, in the defendants’ machine, a substantial change in the mechanical arrangement and construction, and in the operation of the same, from the combination, arrangement and operation of the plaintiffs’ machine.
NOTE. The specification of the plaintiffs’ patent was as follows: •‘The schedule referred to in these letters patent, and making part of the same: Be it known that we, George N. Tatham and Benjamin Ta-tham, Junr., both of the city of Philadelphia, and state of Pennsylvania, have -invented certain new and useful improvements in machinery or apparatus for making and manufacturing pipes and tubes of lead, tin and other metallic substances, and their alloys. And we do hereby declare that the following is a full, clear and exact description of the construction and operation of the same, reference being had to the accompanying drawings, making part of this specification: Our invention of these certain improvements applies principally to the ‘machinery or apparatus for making or manufacturing pipes and tubes from lead, or a mixture or compound of lead with other metals, as tin, or zinc, or any other compound or alloy of soft metals capable of being squeezed or forced, by' means of great pressure, from out of a cylinder or receiver, through or between apertures, dies and cores, when in a solid state,’ described and set forth in the specification of a patent granted to Thomas Burr, of Great Britain, and also described in the first volume of the first series of the London Journal of Arts and Sciences, as therein will appear; and our said invention is applicable in part also to other machinery for manufacturing leaden and other metallic pipes, which will be hereinafter referred to. In the plan described by Thomas Burr, the core (for the formation of the inner diameter or calibre of the pipe) is attached to the end of the piston, and, advancing before it through the cylinder, became bent and twisted out of centre with the dies, thus preventing or destroying the uniformity of thickness or the centrality of the bore of the pipes. This defect resulted from the difference of expansion and contraction, and from the extreme pressure required to drive out the solid metal, and from several other causes, the effect of which was to render that ¡fian ineffective and ineligible. These defects it is the object of our improvements to remedy. Our said improvements may be fully understood by referring to the accompanying drawings, and to the explanations thereof contained in this specification. We use a powerful hydraulic press, which is partially represented at figure 1. In this figure a a, is the cap or top of the press; b b, the base or frame of the bottom thereof, inclosing the great cylinder and the ram, which are not here exhibited. COCO, are the upright wrought iron pillars of the press. The pipes, the safety-valve and other parts of the hydraulic press are not here represented. This engine is so well known, and may be constructed in such variety of forms, as to render a description of it unnecessary, and the figure in the annexed drawings is intended only to exhibit the relative arrangements of the other parts of the apparatus. We use a strong iron cylinder, constructed in a manner substantially resembling that described by Thomas Burr, and intended for precisely the same purposes. The die is secured at the upper end of the cylinder between a circular plate and the top of the cylinder, in an aperture or recess fitted to receive it. The top of the cylinder is attached by means of screws or bolts, or otherwise, thereto, so as to be easily removed and replaced. The cylinder, with its several appurtenances. is to be firmly bolted or secured to the top. of the hydraulic press. It is represented in perspective at A, in figure 1. and in section at A A. in figure 2. k k, figure 2, is a section of the die, which is a polished steel ring. m. m. is the circular plate with a large aperture through it for the passage of the metal towards the die. n. n. is the top of the cylinder. X X,1 figure 2. is a section of a part of the top of the hydraulic press, which part has an aperture (i i) in the form of an inverted cone, to allow access to the cylinder, for the purpose of charging it through the dies or other apertures, and for the passage of the pipes or tubes. The aperture is hidden at figure 1. The piston, B B, (operating within the cylinder,) is bored accurately throughout its length, so as to receive and fit a long core-holder, upon which it is to move or slide easily up and down, being at the same time furnished with proper packing. The hollow piston is exhibited in its place, in perspective, at B, figure 1; and in section, at B B, figure 2. Its parts are shown detached at a and b, in figure 5, and a section of the face at C. Its packing (around the long core-holder) consists of tight rings occupying the places indicated at figure 2 by the letters x x; but it may be packed in other ways in common use. and well known to machinists. The face C should be made of cast-steel. It is secured to the body of the piston by means of bolts or screws. The piston is secured in its place, upon the stable or platform of the hydraulic press, in any convenient manner. We employ a east iron fixture, open in front to receive the piston-head, grasping the same, and, being firmly bolted to the table, is strong enough to bear the high degree of force often required to extract the piston from the cylinder, after it has been driven home. This instrument is represented in its place upon the table at C, in figure 1, and in plan at figure 3. y, and in transverse section at z. We employ a long core-holder. which is a strong round rod of iron or steel, accurately turned and polished, so as to move or slide easily and truly through the hollow piston, fitting the same exactly. One end of this long core-holder is to be securely attached (by a pin or otherwise) to strong iron frame-work, below the table or platform of the press. The core-holder is to be sufficiently long to pass upwards: through the table or platform! through the piston. and through the middle of the cylinder, to its discharging end, where it is to hold (in the centre of the diel a core or mandrel, attached, screwed or bolted into its end: or is itself to be tapered, if necessary, to the size required for the interior diameter or calibre of the pipes or .tubes. The long core-holder is exhibited in its place at D, figure 1, and in section at D, figure 2. and detached.at D, figure 4, where several different plans for its construction next the core are exhibited. The iron framework securing the end of the long core-holder is to be made with several arms, each to be firmly attached to one of the wrought-iron pillars of the hydraulic press. This frame is represented in perspective, in its place, at E E. in figure 1. and in plan, at figure fi, where the relative positions of the pillars that supnort the table or platform of the press are exhibited at e. h. g. The lower part of the framework must be placed at such a distance above the hydraulic ram-head as not to interfere with the rising of the same, when the press is in action. This distance should be of the length of the piston at the least. The table or platform ■of the press is to be supported by strong iron pillars, two, three or four in number, standing between the arms of the framework fixture last described. The table is seen at P P. figure 1. It is to slide upon the wrought-iron pillars of the press, which thus serve as guides to it. The pillars supporting the table are represented atGG G, in figure 1. They are to stand upon the ram-head, which is a solid iron fixture upon the top of the ram itself, and is seen at H. in figure 1. The ram-head is to contain an aperture large enough to permit the end of the long core-holder to descend into the hollow of the ram. when occasion may require the removal of the piston, or a change in any of the different instruments. The operation of the machinery is, in most respects, the same as that described by Thomas Burr, to whose specification we here particularly refer. The several parts being adjusted in their places, as at figure 1, the piston being lowered, the cylinder is filled with melted metal, through the aperture between the die and the core; or, if preferred, through an aperture made for the purpose in the cylinder, which is to be stopped with a screw-plug or otherwise. The space occupied by the metal in the cylinder is represented in the sectional drawings by a tint .of red color. Upon the metal in the cylinder becoming ‘set’ or solid, the press is to be set in action, and, as the ram of the press rises upwards, carrying with it the pillars, and the table or platform upon them, the piston (sliding upon the stationary long core-holder) is driven into the cylinder, and the metal therein is forced upwards between the core and the die, and issues above the top of the press in the shape of a pine or tube.. Lead perfectly cold, and even harder metal, may be driven by this machinery, and formed into pipes or tubes.*716'One word upon the question of damages. As there has been no serious question made on the subject, I shall simply call your attention to the principle that must govern. It seems that the defendants have made 711,551 pounds of pipe in their , machine within the time for which the plaintiffs claim they have been guilty of infringing. The price of lead pipe, during that time, was six cents per pound, except for a small quantity, which was sold at five cents and three quarters per pound. The price of pig lead was about four cents and a half per pound, during the same period. That would make a difference of one cent and a half per pound. But, out of this, the cost of manufacturing the pipe must be taken. What that is, is open to a good deal of observation. One witness states that the plaintiffs could have made it, in very large quantities, for one-eighth of a cent per pound. The rule in these cases is to give the actual damage or loss incurred by reason of the infringement, and that is the profits which the plaintiffs would have made if they had not been embarrassed by the interference of the defendants’ machine. Because, the law presumes that the plaintiffs would have had the pat-tronage which was diverted by the defendants. The profits which the plaintiffs have lost in consequence of the infringement, afford, therefore, a criterion by which to determine the amount of damages they have sustained.
The infringement claimed on the part of the plaintiffs took place between September, 1847, and April, 1848. It is claimed that they are entitled to the damages which they have actually sustained, - together with interest upon the same from that time down to the present. My own view of this question is, that the jury, in estimating the damages, may take into account the interest, if they choose, and give it by way of damages. They may take into account in estimating the damages, the fact that the party has been deprived of them from the time the infringement took place down to the present time.
“We do not intend to limit or confine ourselves to the precise plan here above described of forcing the piston upwards into the cylinder, and of causing the pioe to issue above the press, since the same results will be produced when the action of the machinery is reversed, by securing the piston to the under part of the top of the hydraulic press, and bolting the cylinder upon the table or platform; thereby causing the cylinder to advance upon the stationary piston, and forcing the pipe downwards through an aperture in the table made to admit its passage. In this reversed mode of operation, it would be necessary to construct upright shafts or pillars, standing noon and secured to the table, and made to slide through boxes fitted in the top of the press. These uprights are to be connected above the top of the press, by a strong crossbeam. to the centre of which the end of the long core-holder is to be attached. The core-holder should slide through a box in the top of the press, and also through the stationary hollow piston, and, reaching to the bottom of the cylinder, it must there hold a core or mandrel in the centre of the die, as before described. When the press is set in motion, the core-holder will rise with the upright framework and the cylinder, fixedly preserving its relative position with the die at the bottom of "the cylinder. Figure 7 is a representation (partly in section) of this reversed mode of operation. A, is the cylinder reversed. having the die now at the bottom. B, is the hollow piston, secured to the top of the press. C C. are the upright pillars of the framework. D D. is the cross-beam thereof. E. is the long core-holder depending from the crossbeam. In this latter form or manner of arrangement we intend to apply the foregoing improvements to the apparatus for manufacturing pipes or tubes from lead or other metallic substances, invented by Charles and John Hanson, of Great 'Britain, for which letters patent of the United States were granted to the present inventor, Benjamin Tatham, Junr., and to Henry B. Tatham, of the city of Philadelphia, under assignment from the said Charles and John Hanson, before patent issued, and recorded preparatory thereto, which letters patent are dated the twenty-ninth day of March, eighteen hundred and forty-o,ne. We do not claim as our invention any part of the cylinder, nor of the dies, nor of the arrangement thereof in the cylinder, nor the maimer of adapting these to the hydraulic press, nor the mode of operation generally, all of which have been substantially described in the specifications of the patents of Thomas Burr, and of Benjamin and Henry B. Tatham, assignees of Charles and John Hanson, heretofore referred to. But what we do claim as constituting our invention,, and desire to secure by letters patent, are: First. The long core, or core-holder, formed and held stationary with relation to the dies as described. Secondly. We claim the constructing of the piston B, hollow, in the manner described; and the combination of the same with the long core, or core-holder, upon which the piston slides. Thirdly. We claim, as a modification of our invention, the arrangement and. combination of the several parts above mentioned as exhibited in what has been termed ‘The Reversed Arrangement,’ shown at figure 7, in the accompanying drawings.”