[Cite as State ex rel. Metcalfe v. Indus. Comm., 121 Ohio St.3d 347, 2009-Ohio-1220.]
THE STATE EX REL. METCALFE, APPELLANT, v. INDUSTRIAL COMMISSION OF
OHIO ET AL., APPELLEES.
[Cite as State ex rel. Metcalfe v. Indus. Comm.,
121 Ohio St.3d 347, 2009-Ohio-1220.]
Workers’ compensation — Violation of specific safety requirement — Ohio
Adm.Code 4123:1-5-05(D)(2) — Commission’s denial of award upheld.
(No. 2007-2275 — Submitted February 17, 2009 — Decided March 24, 2009.)
APPEAL from the Court of Appeals for Franklin County,
No. 06AP-830, 2007-Ohio-6180.
__________________
Per Curiam.
{¶ 1} Nicholas Metcalfe died in an industrial accident. After a claim for
death benefits was allowed, appellant, Kimberly Metcalfe, his widow, moved
appellee Industrial Commission of Ohio for an additional award, alleging that
Nicholas’s employer, appellee Ultimate Systems, Ltd. (“USL”), had committed
several violations of specific safety requirements (“VSSR”). The commission
denied her application, and the court of appeals upheld that order, which now
brings the matter here.
{¶ 2} USL makes flooring materials. One of its products was a rubber
and polyurethane compound commonly used in gyms and health clubs. At the
time of Metcalfe’s accident, a bulk loading system was used to manufacture the
material. The system consisted of a pellet-feed system, wet auger, weigh hopper,
and mixer. The latter two are the focus of this litigation.
{¶ 3} The mixer was tub-shaped and approximately 32 inches deep and
30 inches across. For this particular operation, it combined a polyurethane glue
mixture with dry rubber buffings from the weigh hopper, which was suspended
SUPREME COURT OF OHIO
immediately above it. The hopper had clamshell doors that operated
pneumatically to dispense the buffings.
{¶ 4} The mixer needed daily cleaning, which was usually done near the
end of the second shift. Both management and employees described this as one of
the worst jobs in the plant. The employee assigned to the task had to scrape the
semihardened plastic from the inside of the mixer. To do this, the worker was
given a scraper, an air hose to blow out the scrapings, a crock pot full of hot wax,
and a brush to coat the mixer blades and the inside of the mixer with wax to
reduce the likelihood that the glue mixture would adhere to the blades and mixer.
The job could take between 45 minutes and one and one-half hours, depending on
the type of materials run that day.
{¶ 5} In addition to the sheer physical exertion required, the task was
complicated by the layout of the equipment. The mixer and hopper were located
on an elevated platform that backed onto a wall. The safest way to clean the
mixer was for an employee to kneel on the platform’s catwalk and reach into the
mixer. Unfortunately, that method was not the most effective for two reasons.
First, the distance between the suspended hopper and the mixer below was only
nine inches. Second, the mixer was over two feet wide, with no access to the
back side because the mixer was flush against a guardrail. Consequently, the only
access to the mixer was from the front, which, as the staff hearing officer
observed, made it “very difficult to reach across the 30 inch face, through the 9
inch opening, to clean the back wall of the mixer.”
{¶ 6} To more easily and effectively clean the mixer, some employees
devised a much more dangerous cleaning procedure. Rather than clean from the
outside, they would open the hopper doors to allow for clearance and then crawl
into the mixer. This method allowed the employee to sit or kneel in the mixer
with his head and torso between the open hopper doors.
2
January Term, 2009
{¶ 7} Nicholas Metcalfe was cleaning the mixer this way on the night of
August 15, 2002. But he could not have known that one of the valves controlling
air pressure to the hopper doors had failed. Air was slowly bleeding out of the
lines, and when the pressure was exhausted, the hopper doors closed, crushing
him.
{¶ 8} Investigation revealed that Metcalfe had properly locked out the
controls to the mixer. There was, however, no way for him to lock out the weigh
hopper controls, one of the violations appellant alleged in her VSSR application.
Former Ohio Adm.Code 4121:1-5-05(D)(2), now 4123:1-5-05(D)(2), required:
{¶ 9} “Auxiliary Equipment
{¶ 10} “* * *
{¶ 11} “(D) Machinery Control.
{¶ 12} “* * *
{¶ 13} “(2) When machines are shut down.
{¶ 14} “The employer shall furnish * * * a device to lock the controls in
the ‘off’ position or * * * warning tags when machines are shut down for repair,
adjusting, or cleaning.” (Emphasis added.)
{¶ 15} A commission staff hearing officer denied the VSSR application.
Although he found that USL did not furnish a device to lock the weigh hopper
controls in the off position, he also found that the absence of a lockout device was
not the proximate cause of Metcalfe’s accident. The failure of the pneumatic
valve’s solenoid, he wrote, caused the hopper doors to close, so even if the
controls had been locked out, it would not have prevented the air pressure from
bleeding out of the lines.
{¶ 16} Rehearing was denied.
{¶ 17} Appellant petitioned the Court of Appeals for Franklin County for
a writ of mandamus ordering the commission to vacate its decision and allow an
award for a VSSR. The court denied the writ, finding no abuse of discretion in
3
SUPREME COURT OF OHIO
the commission’s conclusion that USL’s noncompliance with Ohio Adm.Code
4121:1-5-05(D)(2) had not proximately caused the industrial accident.
{¶ 18} This cause is now before this court on an appeal as of right.
{¶ 19} Like the court of appeals, we find that the commission did not
abuse its discretion in denying VSSR liability. The question raised by our review
is whether the commission reached the right result for the wrong reason. The
commission’s conclusion is inherently based on a determination that Ohio
Adm.Code 4121:1-5-05(D)(2) applied to these facts. We do not believe that it
does.
{¶ 20} Ohio Adm.Code 4121:1-5-05(D)(2) required the employer to
supply a device to lock a machine’s controls in the off position “when machines
are shut down for repair, adjusting, or cleaning.” The fatal machine in this case
was the hopper, not the mixer, and two findings in this regard are crucial. First,
the staff hearing officer specifically found that part of the cleaning procedure
required the employee to blow out the dust and buffings in the weigh hopper.
This meant that regardless of whether the employee climbed into the mixer, the
hopper doors still had to be open for some part of the cleaning process. Second,
the commission’s safety-violations investigations unit reported that for those
doors to be opened and kept open, the hopper controls had to be in the on
position:
{¶ 21} “There is a knob on the main control panel that activates the
pneumatic valve which opens the weigh hopper doors. The pneumatic valve is
designed to hold the weigh hopper doors in the open position until the knob is
turned to the closed position. The pneumatic valve had to be manually activated
prior to the Decedent climbing in the mixer and inside the weigh hopper.”
(Emphasis added.)
{¶ 22} Metcalfe could not, therefore, accomplish all of his assigned duties
with the hopper’s controls in the off position, and therefore Ohio Adm.Code
4
January Term, 2009
4121:1-5-05(D)(2) is inapplicable. See State ex rel. Harris v. Indus. Comm.
(1984), 12 Ohio St.3d 152, 12 OBR 223, 465 N.E.2d 1286. In Harris, the
printing press at issue had to be running in order to clean it. The claimant was
injured while cleaning the press and asserted a violation of Ohio Adm.Code
4121:1-5-05(D)(2). The employer argued that because the press was on, it was
not “shut down” for cleaning, and the regulation did not apply. The claimant, on
the other hand, argued that because the press “was not engaged in the printing
process,” it was in effect shut down, and Ohio Adm.Code 4121:1-5-05(D)(2)
controlled.
{¶ 23} We agreed with the employer:
{¶ 24} “The purpose of this safety rule is to guard against the possibility
that a machine might turn on unexpectedly, thereby catching a repairman or
another nearby person unawares. * * * It was reasonable for the commission to
hold that the rule does not apply when the machine is already running, because
the fact of its running, itself, provides adequate warning.” Id at 154, 12 OBR 223,
465 N.E.2d 1286.
{¶ 25} As in Harris, Metcalfe could not have done all the cleaning tasks
required with the hopper controls in the off position, and Ohio Adm.Code 4121:1-
5-05(D)(2) does not apply. Appellant is not entitled to an additional VSSR award.
{¶ 26} For the reasons stated above, the judgment of the court of appeals
is affirmed.
Judgment affirmed.
MOYER, C.J., and PFEIFER, LUNDBERG STRATTON, O’CONNOR,
O’DONNELL, LANZINGER, and CUPP, JJ., concur.
___________________
Larrimer & Larrimer and Thomas L. Reitz, for appellant.
Richard A. Cordray, Attorney General, and Stephen D. Plymale, Assistant
Attorney General, for appellee Industrial Commission.
5
SUPREME COURT OF OHIO
Bugbee & Conkle, L.L.P., and Gregory B. Denny, for appellee Ultimate
Systems, Ltd.
______________________
6